![]() ![]()
Enter the information as shown below, then click. If the check box for is unselected, then click the check box to select it. For Windows 2000: From the menu, click, then click. Step 1: Settings for Windows 2000/XP 1 Log on to Windows as a member of the "Administrators" group. Decide on setting values only after careful discussion with the network's administrator. In a large network, unsuitable settings may have a major impact on the functioning of the entire network. Making the Settings for Windows 2000/XP Important! The explanations in this section assume a small-scale network using a single hub. Net Tool Windows 95/98/Me/2000/XP Mac Tool MacOS X MacOS 9.x (CarbonLib extensions version or later required) 3Ħ 2. ![]() ![]() Making the Settings for MacOS X" For the Network Administrator To make the settings for Roland-PrintServer in step 2, you use either "Net Tool" or "Mac Tool." You can run these in the following operating environments. Making the Settings for Windows 2000/XP" Macintosh (MacOS X) See p.8 "3. Refer to the following for specific setup procedures. #Roland Print Server Net Tool software#Step 3 Set the output port and the like for the software RIP. Step 2 Set the IP address and the like for the Roland-PrintServer. Setup Sequence Step 1 Enable the TCP/IP protocol for Windows or Macintosh, and make the settings for the IP address and the like. Getting Started Overview of Settings The software RIP packed with a printer uses the TCP/IP. Hub Roland-PrintServer (RIP) Computer 2ĥ 1. For connection to a hub, use straight cable. Ethernet Cable Connection Use Category 5 twisted-pair Ethernet cable. Not all functions may be available for use. * The usable features of the Roland-PrintServer are dependent on the printer it is combined with. It is compatible with 100Base TX and 10Base T (switched automatically). There are two types: one built in to the printer or the like, and an external type. via Ethernet and use them in a network environment. Getting Started About the Roland-PrintServer The Roland-PrintServer makes it possible to connect printers and other devices from Roland DG Corp. Copyright 2002 Roland DG Corporation 1Ĥ 1. Other company names and product names are registered trademarks or trademarks of their respective holders. Adobe and Acrobat are trademarks of Adobe Systems Incorporated. #Roland Print Server Net Tool mac os#Macintosh, Power Macintosh and Mac OS are registered trademarks or trademarks of Apple Computer, Inc. 9 Step 3: Port Settings for the Software RIP Appendix Roland-PrintServer Reference What to do if Resetting the Roland-PrintServer Windows is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. 5 Step 3: Port Settings for the Software RIP Making the Settings for MacOS X. 2 Overview of Settings Making the Settings for Windows 2000/XP. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any article made using this product.ģ Table of Contents 1. ![]() assumes no responsibility for any direct or indirect loss or damage which may occur through use of this product, regardless of any failure to perform on the part of this product. If you find any misprint or error, please inform us. #Roland Print Server Net Tool manual#The operation manual and the product have been prepared and tested as much as possible. The contents of this operation manual and the specifications of this product are subject to change without notice. Unauthorized copying or transferral, in whole or in part, of this manual is prohibited. #Roland Print Server Net Tool full#To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely and store it in a safe location. To connect and use the software RIP included with the printer with a network, make the settings as described in this document.Ģ Thank you very much for purchasing the product. 1 Roland-PrintServer Network Settings Guide If you're using the software RIP from Roland DG Corp., then this document is for you. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |